You can also select Network Card to search for the IP Camera.
To keep the playback function consistent, the SD card will automatically overwrite the earliest recording.Ĭomputer Browsing Access Download Search Toolĭownload Software from the website ( ) or insert the Mini CD into your computer then install the search tool onto your computer. Note: The files on the SD card cannot be deleted. IMPORTANT: You Need to change the camera time to the local time zone first! Recording and alarm, the default recording is all day APP push is off by default Recording time period and alarm time period can be customized. Old password: “admin“ It is recommended that you select a new password, and WRITE it down so you don’t forget.ĥ.6.5 Set factory default settings of the camera it may not be 41, therefore if you would like to know all the function commands for the camera, pls contact support via email at: Ĭlick “Change Password” to modify the password. All functions of the camera use this method for setup, but different cameras may have different commands, as an example if you would like to set the cruise function to P-1 then it should be 41, however, for P2 or P14 etc. Note: This command pre-set is just one example of the camera command. Input “41” then click Setting(“Submit”on the web,”set”on HIP2P), auto cruise will stop.
You can choose any number of positions from 1-16 you want to set up.Īdjust the camera rotation to the first point you want to monitor on the app input “1” then select Setting Īdjust the camera rotation to the second point you want to monitor on the app input “2” then select Setting ……until you set up your desired areas up to16 points……Īfter you set up your 16 points, input “41” then click transfer(“Call”on the web,”Goto”on HIP2P).
There are 16 different areas that you can set for Auto Cruise. Remarks: HD is a higher-definition display effect than SD (recommended to use when the network is go) When finished, Open the ‘CamHipro’ APP.ī) Use Search Nearby Devices follow the below steps.ġ.Please make sure that the camera has been connected to the router’s Wi-Fi.Ģ.Please make sure that your cell phone is connected to the same Wi-Fi channel as the camera.ģ.If there is no camera on the device list, please move closer to the camera and refresh.ĥ.6.1 Micro SD Card Video files playback and downloadĬaution: if you downloaded the recorded video files from a PC, then the files can only be played via Hiplayer.ĥ.6.2 Local files, device list and add new cameraĬlick to view the local file of different cameras.;click to change the camera device list + click to add a new camera.ĥ.6.3 Pre-set point and auto cruise (For PTZ)Ĭlick the camera in real-time monitor - turn to next page - preset position Set your camera to the Router’s Wi-Fi, following the steps below:Ĭonnect the Camera by Searching Nearby DevicesĪ) Connect the camera to the power supply and the camera will start its self-test mode, which should take about 15 seconds. Note: Only when the mobile phone is approximately 9 – 16 feet away from the camera can the Hot-Spot signal be detected, when the Hot-Spot is detected, you should then turn off mobile data when the camera is connected to the camera’s Hot-Spot.Īdd your camera to ‘CamHipro’ APP following the steps below. The name of Wi-Fi Hot-Spot is the UID on the camera example: (Wi-Fi name:IPCAM-900139)Ĭamera default Wi-Fi Hot-Spot password: 01234567 Your phone should auto search and find the Wi-Fi signal of the camera. On your cell phone go to “settings” then select “Wi-Fi”. The following adding instructions are based on IP cameras.Ĭonnect to IP Camera Hot-Spot and then Configure Wi-Fi Choose different adding methods according to different types of cameras, because common IP cameras cover various adding methods. Install the APP, connect the mobile phone to the WIFI network, enter the APP and click the Add Device button to enter the Add Device interface. Mobile APP CamHipro Connection Connect the Camera by Network cable Also we would recommend: Tinycam, Ip Pro3, or ISpy.
MachineLearning/Anomalous.97%, D:\DOWNLOADS\QPLUS15-ENG.Download APP“CamHipro”in Google Play or Apple Store, or scan the QR Code to install.